Extreme 270° Low Cure Plastisol Ink White – For Cotton, Polyester & Blends

Extreme 270° Low Cure White Plastisol Ink is the white to match our Extreme Low Cure line — a high-opacity, dye-migration-resistant white that fully cures at just 260–280°F (270°F nominal) and prints on 100% cotton, 50/50 blends, and 100% polyester, direct or as an underbase. The ultra-low cure keeps polyester dyes from bleeding and protects heat-sensitive garments from scorch, while staying low-bleed with great stretch. CPSIA-compliant and phthalate-free, made in Hackensack, New Jersey.

Pint through 5 gallon. Heat cure. Made in the USA.

Also available in larger quantities — 30-gallon and 55-gallon drums; call 877-937-6400 for volume and discount pricing.

Features & benefits

• Extreme low cure — 260–280°F — the lowest cure in our line; fully fuses cool to fight dye migration and scorch
• Prints all three fabrics — 100% cotton, 50/50 blends, and 100% polyester
• High opacity — bright, dense white; direct print or a dependable low-cure underbase
• Dye-migration resistant — the cool cure keeps polyester dyes from ghosting into the white
• Low-bleed & great stretch — clean white that flexes with the garment without cracking
• Protects heat-sensitive garments — ideal for poly, performance and sublimated blanks
• Pint to 5 gallon (plus 30 & 55 gallon drums) · CPSIA-compliant & phthalate-free, made in the USA

Always run a test print first. Before any production run, print and fully cure a test on your exact garment and check opacity, hand, dye migration and wash-fastness. It's the best habit in the shop — if you're not sure on settings, call us at 877-937-6400 before you run the job.

What it prints on

• 100% cotton — full opacity, bright white at low temp
• 50/50 cotton/poly blends — the cool cure holds back dye migration
• 100% polyester — jerseys, performance and sublimated garments; low cure is your best defense against bleed and scorch
• Runs as a low-cure flash underbase under colors on darks

Printing & curing

• Mesh: 110–160 for maximum opacity; up to 200+ for a lighter deposit
• Squeegee: 65, 75 or 80 durometer — or a 70/90/70 triple durometer
• Flash: 240–260°F when used as an underbase; keep flash low and brief on synthetics
• Cure: curing is a time-and-temperature process — bring the full ink film to 260–280°F (127–138°C); the low cure is what keeps polyester dyes from bleeding; confirm with a temp gun or donut probe, not dryer air temp

Recommended companion products

• Nylon Bond 289 Additive — mix into this ink to bond prints to nylon and other slick synthetics (catalyst; stir in a small amount, limited pot life, always test first).
• IronBlock LC Grey Blocker Underbase — 270°F low-cure grey underbase for the toughest dye-migration jobs.
• Quick Flash Reducer — thins for easier printing.
• Soft Hand Base — softer hand feel.
• Cleanup: OPTI Wash 125 and OPTI Spot 303.

Safety, PPE & storage

• Wear nitrile gloves and safety glasses; avoid prolonged skin contact with uncured ink.
• Print with adequate ventilation; vent your dryer.
• Always stir before use.
• Storage & shelf life: keep sealed, out of sun. Shelf life 1–2 years. As a low-cure ink, store at 60–80°F. In high heat expect container expansion — open carefully. Do not freeze.
• Refer to the Safety Data Sheet before use.

Compliance

CPSIA compliant (16 CFR 1303 <90 ppm; CPSIA §101 <100 ppm total lead) — safe for children's apparel. Phthalate-free.

⚠ WARNING (California Proposition 65): This product can expose you to chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov.

Questions?

Total Ink Solutions
200 South Newman Street, Unit 4 & 5
Hackensack, NJ 07601
Phone:877-937-6400 · Fax: 201-487-9620
Email: sales@totalinksolutions.com